Rice-lake 880 Performance Series Indicator/Controller Techni Uživatelský manuál Strana 11
- Strana / 120
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
PT
T
Introduction 5
1.4 Indicator Operations
Basic 880 operations are summarized below:
1.4.1 Toggle Gross/Net Mode
1. Press
GROSS
NET
B/N
to toggle the display mode between gross and net.
Note
Net mode is only available if a tare value has been entered or acquired, the net value is the gross weight minus
the tare. If no tare ha
s been entered or acquired, the display remains in gross mode.
A lit LED next to the Gross (Brutto in OIML) or Net on
the display indicates the current mode.
1.4.2 Toggle Units
1. Press
UNITS
to switch between primary and secondary units. The current units LED will be lit.
1.4.3 Zero Scale
1. In gross mode, remove all weight from the scale and wait for the LED to light.
2. Press
ZERO
. The
0
LED lights to indicate the scale is zeroed.
Note
The scale must be stable and within the configured zero range, for the scale to be zeroed. If the scale cannot
be zeroed, NOZERO will
be displayed.
1.4.4 Acquire Tare
1. Place container on scale and wait for the LED to light.
2. Press
TAR E
to acquire the tare weight of the container. Net weight is displayed and the T LED lights to
show the tare value was entered.
1.4.5 Remove Stored Tare Value
1. Remove all weight from the scale and wait for the LED to light.
2. The display should read zero and the
0
LED should be lit, zero the scale if needed.
3. Press
TAR E
(or, in OIML mode, the ZERO key). Display shifts to gross weight and the Gross LED is lit.
Note
If keyed tares are allowed, press
TAR E
to open the keyed tare prompt. To clear the tare press
TAR E
again.
T LED
Indicates that a tare has been acquir
ed and stored by the system.
PT LED
Indicates that a preset tare weight has been keyed in or entered via the EDP serial port.
R1 R2 R3
Bluetooth
Not available at time of publication.
R1, R2 and R3
Current weight range for multi interval or multi range.
Key Function
Table 1-2. Annunciator Functions
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Související produkty a manuály pro Váhy Rice-lake 880 Performance Series Indicator/Controller Techni
Váhy Rice-lake 920i Grain Program Uživatelský manuál
(14 stránky)
(14 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.133 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce